Patent turbo spiral air blower pressing foot at feeder head.
Four pick up and four forward suck heads with angle adjustment.
Preloading device with rail cart and scaled gate.
Non – stop feeder with automatic pile lift.
Left and right side turbo air blower.
Motorized side adjustment of pallet table.
Electrical double sheet control.
Fine air blast at lead edge for smooth thin paper transport.
Sheet slow down device of feeder belts to assure accurate position of the sheet to the front lays with selective on/off switch.
Synchronizing device to adjust the sheet positioning to the front lay by hand during production.
Bullet catcher on the feeder entrance.
Side lays on both sides push and pull convertible.
Electronic side lay control to check the sheet position.
Four individually adjustable front lays with dial read out at the operation side of the machine.
Two electronic front lay controls by means of Omron Glasfiber optik to control the sheet arrival.
Photo sensor safety barrier at pallet table floor level touching point.
Precision worm gear crank toggle driving system to ensure smooth and dynamic lower platen movement.
Precision stationery upper & mobile platen with optimized structure to reduce deformation under pressure hence less make ready & quick change over.
5mm hardened cutting plate (Hardness HRC 45-50º) with X and Y direction micro adjustment.
(±0.9 each way) on top of 15mm base plate with center line to ensure precision creaser positioning and quick change over. (4mm+1mm hardened sandwich plate as optional. Hardness HRC 45-50º)
Pneumatic push button diechase locking mechanism to ensure safe and operator friendly changing of the die.
Pneumatic clutch/brake for main drive system.
A/C motor drive impression on/off by button.
Digital diecutting pressure tonnage display with maximum pressure limit protection of latest technology.
Seven high precision alloy gripper bar.
High quality pre – stretched gripper bar driving chain.
State – of – art 3 cam index gripper bar driving system to ensure smooth and precise gripper bar intermittent movement.
Torque limit safety clutch to protect the index driving system in case of gripper bar crash.
Double cam driven gripper opener and front lay swing frame without position restore spring for smooth and accurate sheet register and take off.
Air blasting nozzle bar for stretching the thin paper before die cutting.
One push button pneumatic activated safety door of die cutting section, more operator friendly.
Triple action movement of the upper and lower stripping frames with lower spring loaded stripping pins.
Motorized upper frame suspending hoister.
Upper and lower stripping tool mounting frame can be pulled out for job set up and make ready.
Remote control operation panel for jogging the upper frame up and down, easy and safe stripping tool set up and alignment.
Quick stripping tool exchange device (optional).
Mechanical disconnecting of lower stripping frame when it is not in use.
One push button pneumatic activated safety door of stripping section, more operator friendly.
Automatic delivery with non – stop curtain. This curtain moves into the delivery to catch the arriving sheets during the pile exchange.
Five section brush brake each section angle adjustable individually.
Air blower to press down the sheets.
Rear and side joggers with easy position adjustment.
Gripper edge stripping and removing system with conveyor belt to remove the gripper edge waste sideways to the drive side.
Tape inserter with counter.
Safety device to prevent the steel pile plate from clamping on the foot when it reaches at ground level.
Specifications for diecutting:
Maximum die cutting size | 1040 x 720 mm | ||
(Maximum cutting size can be reached at 1040 x 730 mm when the quick locking system is dismantled from the die chase) | |||
Inner size of chase | 1080 x 745 mm | ||
Dimensions diecutting plate | 1080 x 736 mm | ||
Maximum diecutting pressure | 300 T | ||
Maximum mechanical speed | 7500 cycles/hour | ||
ripper margin | 8-16 mm (subject to working environment, sheet quality and operation skills, etc.) | ||
Cutting Rule Height | 23.8 mm | ||
General specifications:
Total power required | 20 KW | |
Power voltage | 380V/50/60Hz | |
Net Weight of Machine | 16 tons | |
Machine Dimensions | 7075(L) x 4155(W) x 2235(H) mm (incl. Catwalk & Preloading rails) |
Specification of paper stock range:
Maximum sheet size | 1050 x 750 mm | ||
Minimum sheet size | 400 x 360 mm | ||
Stock range | a. Paper/cardboard | 80g/m2 – 600g/m2 (subject to quality of the paper) | |
b. Corrugated board | Up to 4mm thickness (subject to quality of the corrugated board) | ||
NO. 1125, TAISHUN RD, ANTING TOWN, JIADING DISTRICT, SHANGHAI, 201814 CHINA
© 2016 Shanghai Eternal Machinery CO., LTD.
Didn’t find the information you need?
Please send emails to export@eterna-shanghai.com